[WillieG]

Last fall I had a major air leak in my front right air hose and had a new one installed at a shop(not the one that did my tag bushings wheel seals and bearing alignment)  So today took it for a ride went through a tight round about near my house and heard a pop clunk in my front right,thought what was that. Drive up interstate about 8mes then back to storage as rain was coming. I did notice stopping on exit ramp pressure dropped to 90psi then while parking in the garage while using a lot of break maneuvering in pressure dropping like crazy and could hear a lot of air. Aired it back up shoot off had my son step on break while I looked under and the fitting at the break chamber was snapped off and also they used Teflon tape on it.In Richards YouTube he said that’s not a good idea. My question is what would cause this hose to bust off?  Too short or over tightened?  If zoom in where the rubber meets the brass it looks messed up too

[[email protected]]

Last fall I had a major air leak in my front right air hose and had a new one installed at a shop(not the one that did my tag bushings wheel seals and bearing alignment)  So today took it for a ride went through a tight round about near my house and heard a pop clunk in my front right,thought what was that. Drive up interstate about 8mes then back to storage as rain was coming. I did notice stopping on exit ramp pressure dropped to 90psi then while parking in the garage while using a lot of break maneuvering in pressure dropping like crazy and could hear a lot of air. Aired it back up shoot off had my son step on break while I looked under and the fitting at the break chamber was snapped off and also they used Teflon tape on it.In Richards YouTube he said that’s not a good idea. My question is what would cause this hose to bust off?  Too short or over tightened?  If zoom in where the rubber meets the brass it looks messed up too

Couple of different scenarios come to mind. They may have cracked the fitting by tightening it too much, and the stress finished it off. Could be the hose was too short, but I would have thought the hose would have given first and not the fitting. In this situation it is possible to plug the line to get you by to get off the road, obviously not a permanent fix. No telling what really happened here, but its always a good idea to put the front tires through all their range of motion after replacing these brake hoses to make sure they are long enough and they are not going to rub on anything.

[WillieG]

It’s odd as there are no more than 30miles on since the hose was replaced

[Richard]

From what I can see in the photo, the hose assembly and install are less than optimum. How about that for political correctness.

You need two things to fix this. The first is an EZ Out to get the broken fittings out of the brake chamber. The second is a new BRAKE hose. Measure the one on the other side, and take that measurement to a fleet pride or similar store, perhaps even NAPA, and tell them you want an air brake hose. They will have a rack of premade hoses with appropriate fittings on each end.

Now here is a trick that will make this way easier. The premade hoses will not usually swivel. So threading both ends without twisting the hose is difficult. Remove the two bolts that hold the brake chamber to the caliper. You can now turn the chamber as you thread the fitting. Reinstall the chamber after the fitting is tightened. Use tape or dope, your preference.

This is an easy fix. Be sure to crib the coach while working in the wheel well.

[WillieG]

The shop that did the brake hose has agreed to pay for the repairs of the failed right front line they installed. I’m getting my transmission fluid and filter serviced at the place that did my tag work,and will have them redo the brake line.What are opinions on doing the left front with a new line right away?   I actually told the other shop to do both front lines when they replaced the one last fall.Of course that place has horrible communication and they didn’t do what I had asked.

[WillieG]

I had the brake hose replaced a second time by the shop that did my tag bushings a month ago.I wad driving back there this am to face a hub cap mount moved a lug nut over.took a hard left turn and the airline snapped again waiting for them to get it in the shop now. I’m not sure what exactly is causing this they said they told them in the shop to make sure it was good full turn to full turn

[BusNit]

I haven't checked my front hoses yet, but on the rear, I had these easy to install self made hoses. The spring relief has a ferrule that bites into the hose and gets locked down by the collar. This allows you to install the hose at your predetermined length and set it up without any twisting. I just finished these and will be undergoing some testing over the weekend. (While I was in there, I replaced the tag axle brake chambers as they were pretty cruddy. Main chambers look very good.

[WillieG]

What the shop figured out was the driver side chamber has the hose connection straight up. The passenger side at some point had been put back on and it was turned inwards maybe 20°. there was a mark on the metal part of the hose that coincided with the control arm. that while turning tight while turning left, maybe associated with a lien would contact that and that’s what must’ve broke that fitting again. so they re-adjusted the passenger brake chamber straight up reconnected it test drove it with some tight turns checked it out again from the pit and it didn’t show any contact.. I also had them put it on a shaker machine which he suggested because I said there was quite a clunk and I was wondering if I had a bushing loose or bad everything checked out

[BusNit]

The clunk on these could also be the generator on the track or the exhaust pipe as it passes out the back of the generator hush box. I was going to say that your fitting looked like it had made contact with something to shear it off like that. Those fittings are robust seeing that I installed a few. Glad it was figured out.

[Jack Houpe]

When the line broke off the brake actuator did it not lock up the front tire?