Posts: 112
Threads: 19
Joined: Mar 2014
(02-14-2024, 03:59 PM)Richard Wrote: Hmmmm disconnect the pump and cap the line. See what happens with your air useage
Took off the 12v compressor. It's not compressing and there was a leak in the check valve. I put a plug in the line. Now I'm holding for 14:15, about a 4 minute improvement. At this rate there must be about 10 more leaks to find just to get me back to 45 minutes.
David and Teresa Brown
1999 Coach 513
Posts: 302
Threads: 30
Joined: Nov 2020
I know I've mentioned it, but it REALLY is worth repeating because it's stinging a lot of us!
Those check-valves are silent demons! They'll leak and you'll not "hear it", nor will you "see it" leak. It would behoove you to embark on a seek and destroy mission for those.
And, as Richard mentioned, be sure to isolate your leveling system; turning it off during this testing. Lower it all the way to the ground...UNLESS you're sniffing the air-bags, 6-pack manifolds, etc.
Keep at it...you'll get there.
Steve & Janice Vance
2015 Newell #1524
Glendora, CA
Posts: 112
Threads: 19
Joined: Mar 2014
Does anyone have part numbers for the very small air lines and fittings that are on the pneumatic doors? I found a very small leak in a fitting, plus Newell stretched the 2 small air lines very tight - like they cut the line a little short and stretched them to fit. I would need to replace the lines and the fittings. Small leak, but all these leaks add up.
David and Teresa Brown
1999 Coach 513
Posts: 493
Threads: 59
Joined: Jun 2022
Are they the 1/8" lines shown on the left in my photo? I got 1/8" tubing from a Parker Store when passing through Grand Rapids, MI. For the 90º fittings, I put a brass Street Ell in and then straight 1/8" compression fitting into the Street Ell. The compression fitting came from Ace Hardware, I believe.
Jim
2014 Newell Coach 1482 Mid Entry 45'8" Valid Slides and Valid Levelling
Posts: 112
Threads: 19
Joined: Mar 2014
(02-16-2024, 11:02 AM)hypoxia Wrote: Are they the 1/8" lines shown on the left in my photo? I got 1/8" tubing from a Parker Store when passing through Grand Rapids, MI. For the 90º fittings, I put a brass Street Ell in and then straight 1/8" compression fitting into the Street Ell. The compression fitting came from Ace Hardware, I believe.
Could be. My photo is a CU. I can get a wider shot. Tubing says Parker Parflex FFT-2A 1/6.
David and Teresa Brown
1999 Coach 513
Posts: 5,412
Threads: 255
Joined: Jul 2012
Richard and Rhonda Entrekin
99 Newell, 512
Maverick Hybrid Toad
Inverness, FL (when we're home
)
Posts: 320
Threads: 4
Joined: Jun 2013
There are rebuild kits out there for the Thomas “Wobl” pumps. About 1/3 the cost of the entire pump.
06 M450LXi 3 slide
Posts: 1,268
Threads: 68
Joined: Sep 2022
If the line are a little short just move the valve, if the valve is leaking Amazon has a $20 replacement.
https://www.amazon.com/dp/B01LWJ3AWG?psc...ct_details
1999 45' #504 "Magnolia"
Gravette, Arkansas
1996 40 XL Prevost Marathon
Posts: 112
Threads: 19
Joined: Mar 2014
02-22-2024, 09:42 AM
Still working my way through the air systems. I'm hearing this sound (in the video) from the air tank in front of the passenger drive axle. Does anyone know what it is? My suspicion is it's letting air out, but I would like to really know.
Having trouble posting a video, but the sound is occasional pinging. It lasts for a second and happens every 10 seconds or so.
David and Teresa Brown
1999 Coach 513
Posts: 1,268
Threads: 68
Joined: Sep 2022
Are you talking about the tank in the bay with the blower for the generator? Can you post a picture? If there is a water separator in that compartment with a electric actuated valve then that might be your problem.
1999 45' #504 "Magnolia"
Gravette, Arkansas
1996 40 XL Prevost Marathon