You are not logged in or registered. Please login or register to use the full functionality of this board...


3/8 Push Fittings
#1

Was chasing down a little leak coming out of my 120v compressor and after I fixed that I found a pretty good sized leak coming out of both of these push fittings on the yellow lines.

Curios of a couple things/

1.) What they feed as it looks like it lust comes into this bay, goes through that union and goes right back out?

2.) Is the solution just a compression fitting?


Attached Files Thumbnail(s)
       

Brad Aden
2003 Newell #653 Quad Slide Cat C-12 engine
Towing 2020 Grand Cherokee Summit
St. Louis, MO
Reply


Messages In This Thread
3/8 Push Fittings - by 360 - 01-02-2023, 05:27 PM
RE: 3/8 Push Fittings - by BusNit - 01-02-2023, 06:08 PM
RE: 3/8 Push Fittings - by folivier - 01-03-2023, 05:33 AM
RE: 3/8 Push Fittings - by hypoxia - 01-03-2023, 08:04 AM
RE: 3/8 Push Fittings - by 360 - 01-03-2023, 05:05 PM
RE: 3/8 Push Fittings - by CaptainGizmo - 01-03-2023, 09:04 PM
RE: 3/8 Push Fittings - by folivier - 01-04-2023, 06:24 AM
RE: 3/8 Push Fittings - by 360 - 01-04-2023, 12:11 PM
RE: 3/8 Push Fittings - by BusNit - 01-04-2023, 05:07 PM
RE: 3/8 Push Fittings - by HoosierDaddy - 01-04-2023, 09:46 PM
RE: 3/8 Push Fittings - by Richard - 01-05-2023, 05:25 AM
RE: 3/8 Push Fittings - by hypoxia - 01-05-2023, 07:07 AM
RE: 3/8 Push Fittings - by smagown - 01-05-2023, 09:30 AM
RE: 3/8 Push Fittings - by folivier - 01-05-2023, 11:05 AM
RE: 3/8 Push Fittings - by 360 - 01-05-2023, 12:02 PM
RE: 3/8 Push Fittings - by folivier - 01-05-2023, 12:09 PM
RE: 3/8 Push Fittings - by 360 - 01-05-2023, 03:47 PM
RE: 3/8 Push Fittings - by CaptainGizmo - 01-05-2023, 06:30 PM
RE: 3/8 Push Fittings - by CaptainGizmo - 01-07-2023, 11:41 AM
RE: 3/8 Push Fittings - by Richard - 01-07-2023, 05:52 PM
RE: 3/8 Push Fittings - by CaptainGizmo - 01-07-2023, 07:35 PM
RE: 3/8 Push Fittings - by 360 - 01-09-2023, 05:23 PM
RE: 3/8 Push Fittings - by 360 - 01-07-2023, 09:35 PM
RE: 3/8 Push Fittings - by folivier - 01-08-2023, 06:15 AM
RE: 3/8 Push Fittings - by 360 - 01-08-2023, 12:03 PM
RE: 3/8 Push Fittings - by CaptainGizmo - 01-08-2023, 12:55 PM

Forum Jump:


Users browsing this thread: 3 Guest(s)