You are not logged in or registered. Please login or register to use the full functionality of this board...


Genset exh slip joint
#20

(01-27-2013, 04:05 PM)rheavn Wrote:  To my total surprise the spray anti-seize worked great! I do not have the 110V air compressor mounted in the genset hush box so it made access to the left side of the genset open. I was able to reach quite a way back. The can came with a short straw that I used. I was able to spray a coating on three sides--top, right(as you look at it) and bottom all the way back to the rear of the hush box without making a mess. I had to use a brush to finish the left side(as you look at it) of the exhaust pipe. Here is a link to the product I used.

http://www.amazon.com/Permatex-81464-Ant...B000HBNVWQ

The spray sounds wonderful, too bad a longer straw isn't readily available as that would be more convenient! It's always a messy job it seems after you think you've washed it all off you find more on your ear or nose!!

Gordon Jones
2000-45'-2slide-#567
Reply


Messages In This Thread
Genset exh slip joint - by rheavn - 12-24-2012, 05:02 AM
RE: Genset exh slip joint - by rheavn - 12-24-2012, 06:26 AM
RE: Genset exh slip joint - by encantotom - 12-24-2012, 07:07 AM
RE: Genset exh slip joint - by Richard - 12-24-2012, 07:31 AM
RE: Genset exh slip joint - by Chester Stone - 12-24-2012, 08:33 AM
RE: Genset exh slip joint - by rheavn - 12-24-2012, 08:34 AM
RE: Genset exh slip joint - by rheavn - 12-24-2012, 07:35 PM
RE: Genset exh slip joint - by Gordon - 12-24-2012, 08:03 PM
RE: Genset exh slip joint - by encantotom - 12-24-2012, 08:12 PM
RE: Genset exh slip joint - by rheavn - 12-25-2012, 04:31 AM
RE: Genset exh slip joint - by encantotom - 12-25-2012, 08:32 AM
RE: Genset exh slip joint - by rheavn - 12-25-2012, 09:27 AM
RE: Genset exh slip joint - by bestgenman - 12-28-2012, 04:53 PM
RE: Genset exh slip joint - by encantotom - 12-28-2012, 05:08 PM
RE: Genset exh slip joint - by folivier - 12-28-2012, 05:19 PM
RE: Genset exh slip joint - by rheavn - 12-28-2012, 06:00 PM
RE: Genset exh slip joint - by encantotom - 12-28-2012, 06:02 PM
RE: Genset exh slip joint - by rheavn - 12-28-2012, 06:20 PM
RE: Genset exh slip joint - by rheavn - 01-27-2013, 04:05 PM
RE: Genset exh slip joint - by bestgenman - 01-28-2013, 03:23 AM
RE: Genset exh slip joint - by rheavn - 01-28-2013, 05:00 AM
RE: Genset exh slip joint - by Chester Stone - 01-28-2013, 10:07 AM
RE: Genset exh slip joint - by Chester Stone - 01-28-2013, 10:59 AM
RE: Genset exh slip joint - by rheavn - 01-28-2013, 11:02 AM
RE: Genset exh slip joint - by rheavn - 01-29-2013, 04:41 AM
RE: Genset exh slip joint - by ron skeen - 01-29-2013, 06:58 AM
RE: Genset exh slip joint - by Chester Stone - 01-29-2013, 11:25 AM
RE: Genset exh slip joint - by bestgenman - 01-29-2013, 05:56 PM

Forum Jump:


Users browsing this thread: 5 Guest(s)