adjusting opening and closing speeds on bode air entrance door - Printable Version
+- Newell Gurus (https://newellgurus.com)
+-- Forum: Technical Discussions (https://newellgurus.com/forumdisplay.php?fid=3)
+--- Forum: Air Operated Systems and Leaks (https://newellgurus.com/forumdisplay.php?fid=33)
+--- Thread: adjusting opening and closing speeds on bode air entrance door (/showthread.php?tid=672)
+- Newell Gurus (https://newellgurus.com)
+-- Forum: Technical Discussions (https://newellgurus.com/forumdisplay.php?fid=3)
+--- Forum: Air Operated Systems and Leaks (https://newellgurus.com/forumdisplay.php?fid=33)
+--- Thread: adjusting opening and closing speeds on bode air entrance door (/showthread.php?tid=672)
adjusting opening and closing speeds on bode air entrance door - encantotom - 04-05-2013
i changed the mac valve out on the bode air door today hoping it would fix my problem. i did learn about how to adjust the opening and closing speed/rate on the air entrance door
on the mac valve there are two set screws. they are pilot screws to adjust the airflow. the top one as you look at the valve in the unit is the open and the bottom is the close. counterclockwise is faster and clockwise is slower. it takes a little playing with but i got it where i want it.
it is best to start with them most of the way clockwise so the door doesnt slam open and close if you put a new valve in.
then back them off a turn or two and check and repeat.
tom
Hitch - pjhorton - 04-07-2013
Yet another place to examine.
We were going from Austin to Miami to have a slide seal replaced. In far nowhere OK, we stopped for lunch and happened to notice our hitch (we tow a twenty foot car trailer) pointing down about 30 degrees. Didn't seem safe to drag the trailer, so we called for assistance. A guy came out with a welding rig. We discovered the hitch is attached to the Coach by two bolts at each end and an L shaped bracket in the middle. The bracket is bolted to the coach and welded to the hitch. We found that the L vertical had failed horizontally due to metal fatigue and over time had caused the welds to fail on the L and on one of the 45 degree support. This allowed the tongue weight (about 425 pounds depending on the odd bicycle) actually bend the hitch bar. The welder replaced the 1/8 inch thick steel L with 3/8 inch steel and did new welds every where on the hitch. After some bending the hitch is now correctly oriented and stronger than ever.
Wouldn't have ever looked at the hitch attachments that closely before.
Another item for the once a year checklist.
Phil & Judy Horton
Coach 470 and a twenty foot car trailer
Currently at Newell
RE: adjusting opening and closing speeds on bode air entrance door - les korcala - 04-07-2013
Scary ! when things can happen so quickly.
I just spoke with couple from MI at teh camground since they had welder warking on their Newmar ( Mountain Aire ) they said that they about to loose their car when husband noticed at the rest stop ( thank God ) that hitch is cracked all over!
They also noticed that they had too, only 2 bolts holding the hitch's frame , he alos said thet another 2 Newmar owwners he met in Alaska had same problem! scary how those rigs go trough inspection!!!!
BTW, he checked some newer Newmars at teh factory and they all have standard 4 bolts on the frames.
I have to get under and see what we got going!
Thanks for heads up !!!
Les
RE: adjusting opening and closing speeds on bode air entrance door - Land Yacht - 07-01-2017
(04-05-2013, 07:09 PM)encantotom Wrote: i changed the mac valve out on the bode air door today hoping it would fix my problem. i did learn about how to adjust the opening and closing speed/rate on the air entrance door
on the mac valve there are two set screws. they are pilot screws to adjust the airflow. the top one as you look at the valve in the unit is the open and the bottom is the close. counterclockwise is faster and clockwise is slower. it takes a little playing with but i got it where i want it.
it is best to start with them most of the way clockwise so the door doesnt slam open and close if you put a new valve in.
then back them off a turn or two and check and repeat.
tom
Tom, my Bode door seems to be closing at a reasonable speed, but the front end of the door does not always come in flat, causing the door to not close fully, or sometimes pop close after binding. If I am on the outside of the coach,and I put 1 finger on the forward edge with just light pressure the door closes flat and slides up to locked position just fine. Do you know how to adjust this? I am thinking the small rod on the top of the door?
Thanks
Mike
RE: adjusting opening and closing speeds on bode air entrance door - encantotom - 07-01-2017
i will go out and look at mine this afternoon.
tom
RE: adjusting opening and closing speeds on bode air entrance door - dbld58 - 09-11-2022
I know this is a really old thread, but it is like watching a movie and loosing electricity 10 min from the end.
I need to adjust my door and have the same scenario as Mike. What is the answer. Sped adjustment or rod adjustment?