Muffler replacement - Printable Version
+- Newell Gurus (https://newellgurus.com)
+-- Forum: Technical Discussions (https://newellgurus.com/forumdisplay.php?fid=3)
+--- Forum: Exterior (https://newellgurus.com/forumdisplay.php?fid=7)
+--- Thread: Muffler replacement (/showthread.php?tid=344)
+- Newell Gurus (https://newellgurus.com)
+-- Forum: Technical Discussions (https://newellgurus.com/forumdisplay.php?fid=3)
+--- Forum: Exterior (https://newellgurus.com/forumdisplay.php?fid=7)
+--- Thread: Muffler replacement (/showthread.php?tid=344)
Muffler replacement - rheavn - 11-18-2012
Looks like it is time to consider muffler replacement as the exhaust tip end is deteriorating. The muffler is a Stemco that has the following markings: Inlet C7
19X 2110C
Does any one have a source?
RE: Muffler replacement - Gordon - 11-18-2012
I just purchased a muffer & air filter from these people.
Good pricing & follow up
http://filterspro.com/results.cfm?searchfor=P524838
RE: Muffler replacement - rheavn - 11-18-2012
Thanks Gordon. I'll call them tomorrow.
RE: Muffler replacement - les korcala - 12-05-2012
My muffler and pipe is starting to go ! I am not sure any weld patch would help anything, will try to get all done in AZ next month.
Looks like owber before us backed up and put good size dent in the muffler and over the time the seams just broke open!
How much is to much to pay for the muffler ? I should get the model number of my old one first..
RE: Muffler replacement - Chester Stone - 12-06-2012
I had the same problem, so we took it off and a welding shop fabricated new metal.
RE: Muffler replacement - rheavn - 12-22-2012
After Chester's advice I started looking at repairing the muffler. Especially since Newell gets almost $900 for one. Was able to get it out and repaired. I fabricated a couple of patches and welded them on to cover & strengthen the deteriorating area which was by the outlet. It had plenty of metal & welded up good. Muffler is now very solid. Two problems I ran into. Very hard to get the clamp off the vertical pipe. Lots of PB Blaster, patience and small turns. I had to cut through the four hanger bolts as they were seized. The rear muffler hanger had broke on one side--I suspect it was broken & I didn't realize it. I was able to reweld the hanger and strengthen it. I've got a little painting to do while it is out. I'm going out today to get a new clamp and then I'll reinstall which should be no problem. Muffler is in pretty good shape now considering its age. Hope this will allow me another 3-5 years before I replace it.
RE: Muffler replacement - Chester Stone - 12-22-2012
Steve, so glad it worked out for you. Here in Mexico, the welders are especially talented and it was no big deal for them. I had to shim the bracket because the bottom of the muffler was dented in a little bit. It's fun to save a buck sometime.
RE: Muffler replacement - les korcala - 12-22-2012
Last owner did hit low spot with base of the muffler and put good size dent in it, so front face plate where the pipe comse out started to crack.
Les
RE: Muffler replacement - rheavn - 12-22-2012
Les,
Yours is worse than mine was, but I think you could find some one to "patch" it. A new muffler from Newell is under $900. A fabrication shop could build a patch or two or three and try to weld it. I say try to weld it because if the metal has rusted too much it may disintegrate when they weld it and you'll have to get a new one anyway. Of course you also have the labor of removing & replacing, which in my case was not a simple unbolt as everything was very rusty & seized. Now you need to weigh how much of the job you are equipped to do yourself & how much you'll need to subcontract. Weigh that against what a new one costs installed. Also consider that a "patch" is a temporary fix, whereas a new muffler will last you many years.
I had the benefit of having all the equipment and material to R&R the muffler, build two patches and weld it up. If it wasn't weldable I would have only lost a little time.
Hope this helps............................
RE: Muffler replacement - les korcala - 12-22-2012
(12-22-2012, 11:34 AM)rheavn Wrote: Les,
Yours is worse than mine was, but I think you could find some one to "patch" it. A new muffler from Newell is under $900. A fabrication shop could build a patch or two or three and try to weld it. I say try to weld it because if the metal has rusted too much it may disintegrate when they weld it and you'll have to get a new one anyway. Of course you also have the labor of removing & replacing, which in my case was not a simple unbolt as everything was very rusty & seized. Now you need to weigh how much of the job you are equipped to do yourself & how much you'll need to subcontract. Weigh that against what a new one costs installed. Also consider that a "patch" is a temporary fix, whereas a new muffler will last you many years.
I had the benefit of having all the equipment and material to R&R the muffler, build two patches and weld it up. If it wasn't weldable I would have only lost a little time.
Hope this helps............................
This might be stupid qestion, but why would you need the original muffler from Newell, You would think with so many coaches up there it has to be after mraket Co.who makes all shapes of them.
While having some small repair in North West I showed our muffler to the owner of the shop and he said it would be some 200-400$ for OM muffler , at the time we had no time to wait for the part.
My mother had cadillac back in 80's and whole two mufflers and pipes were like 600-800$ to replace ! Mufflers and pipes can vary so much in shape and the price you pay for!