Dash Removed Projects - Printable Version
+- Newell Gurus (https://newellgurus.com)
+-- Forum: Technical Discussions (https://newellgurus.com/forumdisplay.php?fid=3)
+--- Forum: Interior Things (https://newellgurus.com/forumdisplay.php?fid=6)
+--- Thread: Dash Removed Projects (/showthread.php?tid=1301)
+- Newell Gurus (https://newellgurus.com)
+-- Forum: Technical Discussions (https://newellgurus.com/forumdisplay.php?fid=3)
+--- Forum: Interior Things (https://newellgurus.com/forumdisplay.php?fid=6)
+--- Thread: Dash Removed Projects (/showthread.php?tid=1301)
Dash Removed Projects - Richard - 03-04-2014
I removed the dash cover to stealth mount the VMS PC cords. While in there I removed an old Motorola car phone. Remember those? And a GPS sender with a serial connection, and two generations of obsolete Satellite wiring.
I'll move the CB mounting to the far left. I don't know why Newell mounted in such an obtrusive place right over the accelerator.
I have a couple of push on air fittings on the air brake cylinder which will get replaced.
I will probably take the dash heat damper box out since the fan is squealing. I'll fix the fan, check the box for proper sealing, and clean the coils.
Based on your inside the dash issues in the past, is there anything you would recommend I check or do while it's in pieces?
RE: Dash Removed Projects - rheavn - 03-04-2014
Check the warning lights to see if they are working. I had 4 or 5 burnt out. They sell the bulbs at Wal*Mart.
RE: Dash Removed Projects - lbrachfe - 03-04-2014
Check all the dampers and the heat/ac flex pipe junctions, I found all kinds of crazy connections in this system as the previous owner was trying to increase air flow with some insane additions to the duct lines. Dry lubricate the fans ..
I also had all kinds of out dated stuff in mine and some wiring that was actually causing a short from a disconnected GPS with power still running through the lines.
RE: Dash Removed Projects - qcj - 03-04-2014
I hot wired my pressure pro. Found a good hot wire that was vacant and wired it up. Worked great. One big problem, when I turned on the ignition it was not hot. Found several wires that way. So if you are going to hot wire something make sure it is hot all the time, if that is what you want.
RE: Dash Removed Projects - smagown - 03-04-2014
I increased the thickness of the wires to my Aux compressor switch. The switch would melt every six months or so from the heat generated by too small a gauge wires going into the back of the switch. They carry 110v. Hasn't occurred since the fix.
RE: Dash Removed Projects - bikestuff - 03-04-2014
Steve,
Can you say more about your Aux compressor switch? Which compressor...where did the wire go?
Thanks,
bill
RE: Dash Removed Projects - folivier - 03-04-2014
Still have the original rearview monitor? Good time to replace it with a nice color one.
RE: Dash Removed Projects - ccjohnson - 03-04-2014
Check all the gauge lights
RE: Dash Removed Projects - Airplane Guy - 03-04-2014
Forest,
Speaking of rear cameras, you have any recommendations?
RE: Dash Removed Projects - smagown - 03-04-2014
Bill:
I didn't trace them but think they go down into the generator blower fan bay up front passenger side. Under the dash I found where the wires were spliced and the wires going into the back of the switch in the dash were overheating and were melting the back of the switch at the spade terminals. I put a larger gauge wire from the splice to the switch and that solved the problem. I'll look for some pics. The Aux compressor is in my generator bay and supplies air to the supply side tank when the engine isn't running.